Lỗi sata2 hard disk s.m.a.r.t failed năm 2024

1. Khi BIOS phát hiện lỗi SMART của ổ cứng HDD SATA, nó sẽ hiển thị thông báo trong quá trình kiểm tra khởi động(POST):

“S.M.A.R.T Status Bad, Backup and Replace. Press F1 to Resume…”

2. Nhấn F1 để bỏ qua cảnh báo và sau đó bạn có thể đăng nhập vào hệ điều hành. Nhưng nếu như không thể khác phục lỗi này, nó sẽ hiển thị thông báo mỗi khi bạn khởi động máy lại, trừ khi bạn khóa(disable) "SMART SELF TEST" trong trình đơn thiết lập BIOS

**Gợi ý：Khi bạn thấy thông báo này nghĩa là ổ cứng của bạn có khả năng hư sớm. Vui lòng sao lưu tất cả dữ liệu và thay thế HDD hoặc cài phần mềm theo dõi/ kiểm tra HDD để đề phòng.

Làm thế nào để tắt "SMART SELF TEST" trong BIOS Setup (Không khuyến khíc​h!)

1. Nhấn F2 trong quá trình khởi động để vào BIOS setup

2. Advanced->SMART Settings->SMART Self Test" --->OFF. (Thiết lập mặc định là "ON")

Nếu bạn vẫn không thể giải quyết vấn đề của mình, hãy tải xuống MyASUS và thử Chẩn đoán hệ thống để khắc phục sự cố.

When your hard drive is beginning to fail, it might start popping up with the error messages on the screen of your computer's monitor. Most likely, your computer gives you the information that a serious disk error occurred in the attempt to read/write drive.

If you are not able to identify the issue, you need to consider any of those error messages as a cause of the damaged hard drive.

Keep powering on the damaged disk is a potential threat to data on it. Try avoiding any, or at least minimizing all unnecessary manipulations with the damaged hard drive, the sooner you disconnect the failed disk from power cable, the better chance is to salvage all your files or even the whole operating system from it.

When Self-Monitoring, Analysis and Reporting Technology (or S.M.A.R.T.) is a monitoring system for computer hard disk drives and SSDs (solid-state drives) enabled in BIOS settings, you may have warning diagnostic messages about the drive problem upon restart:

Hard drive Self Monitoring System has reported that a parameter has exceeded its normal operating range. May or may not indicate a hard drive problem. Strike F1 to continue, F2 to run the setup utility.

No boot device available. SATA 0 installed SATA 1 none SATA 2 installed SATA 3 none

In that case no functioning/usable drive exists in your computer anymore, failed device must be removed and send to HDD recovery lab.

Errors messages In MS Windows, related to Hard Drive Problems

If the operating system cannot get the access to the booting code, system files, or user's data on the hard drive - then, the disk is either: damaged, or not properly connected, or has a corrupted boot code. Typically, as a result - system is halted with the black or blue screen. The hard drive with the missing system files or getting bad sectors, clusters, or missing allocations can provide the same behavior.

Data Error Reading Drive [C]

Drive Not Ready-System Halted

Error Reading Drive [C]

Hard Drive Failure

"Hard Drive Failure" Error message - from running operating system

I/O Error

Missing operating system

Primary Hard Disk Failure

Seek Error - Sector not found

Serious Disk Error Writing Drive

A serious disk error occurred trying to read/write drive

HDD-related error messages generated by MAC OS

Bad file name Bad master directory block Cannot access (drive's letter) because a disk error occurred Directory not found Drive not installed Internal file system error No such volume Not a Macintosh disk Not an HFS volume Read/Write requested for an off-line drive Segment Loader Error The disk (drive's letter) cannot be accessed because a disk error occurred This disk is unreadable by this computer. Do you want to initialize the disk?

Error messages on boot up for PC computers and console Run-time applications

These hard disk's errors happen on the boot or in the attempt to run DOS, Novell, or some console command or utility, or when your computer cannot find or initialize the drive controller or the drive diagnosis failed. Usually indicates damaged or unbootable drive. Check, if your computer BIOS/CMOS is able to identify the model number.

Hard Disk Fail (10), (20), (80) Primary master hard disk fail or Secondary master hard disk fail Primary slave hard disk fail or Secondary slave hard disk fail Drive Not Ready Disk is not formatted Drive is not formatted Disk boot failure, insert system Disk and Press Enter Invalid media, track 0 bad or unusable Invalid media type reading drive C: Invalid / Non System Disk Hard Drive Parameter Table or BIOS Error Hard Disk Install Failure Computer stops at verifying DMI pool data Non-System disk or disk error; Replace and strike any key when ready Format command cannot format the specified disk The disk capacity is invalid Hard disk controller failure

For servers: POST Error Messages on boot up, and test's messages

These messages indicate one or more of the following: Hard drive is not properly setup in CMOS, or hard disk drive is not detectable because it is damaged or failed.